 |
 |
 |
|
INCLUDES: ABS Parts (Cowl, Gun, Exhaust Ports, Radiator Scoop), Clear Canopy,
Pushrods, Full Size Plans, Photo-Illustrated Instructions and
All Wood to Complete the Kit.
REQUIRES: Engine: 2.1-2.8 cu in (35-45cc)(Glow) or 2.5-4.2 cu in (41-70cc)(Gas)
5"* Spinner, Propeller, Engine Mount, Fuel Tubing, Easy Filler Fuel
Valve, 16-20oz Fuel Tank (see commments on multicylinder option)
Main Gear*, Tailwheel Retract, Air Control Kit. (see comment on gear)
Radio: 6 to 7 Channel
Servos: 10 (Standard: 2-Flaps, 1-Retracts, 1-Tailwheel Steering,
1-Throttle
High Torque (over 45 oz/in): 2-Elevator, 1-Rudder, 2-Ailerons
Y-Harness: 4 (Elevator, Flaps, Ailerons, Rudder/Tail Steering)
Servo Extensions (24"): 2
Receiver Battery: 6V 1200mAh
Covering: Four to Five 6 Foot Rolls and Matching Paint
Misc. Items: Two 5" Main Wheels, 1-3/4" Tailwheel, Wheel Collars,
Five Heavy-Duty Control Horns, Twenty Six Heavy-Duty Hinge Points,
Sixteen #6x1/2" Sheet Metal Screws (for mounting the retracts)
1/2" Foam Rubber Padding, Switch and Charge Mounting Jack,
Pull-Pull Cable System for Steerable Tailwheel, Covering Tools,
Building and Field Equipment. .
COMMENTS: This kit can be fiberglassed or covered with film covering.
After market items availabe (retracts, cockpit interior, pilot, etc.)
(see optionals on the Accessory Completion Guide for these items)
GEAR: FIXED LANDING GEAR IS NOT INCLUDED
If you are wanting to used fixed gear use ROBQ1640
Kit is designed for Robart custom gear. If using other gear
gear must contact support for copies of ribs need to be hand cut
to mount standard retracts.
Spinner: ZINQ spinners will not fit this model due to their mounting.
The O.S. FF-320 should have plenty of power to fly the Giant P-51. The cylinder
will protrude through the sides of the cowl. The engine is only a couple of oz
heavier than an US 41 and shouldn't be a problem.
(The 5cyl. radial won't fit in cowl.)
The ST3250 will work okay in the giant 51 also. Don't expect super
speed or much vertical performance but will work fine for most
maneuvers.
DECALS: P51GD01-1 per kit,
P51GD02-1 per kit,
P51GD03-2 per kit (decals are only available from GPM 217-398-8970x3)
P51GD01 includes: (2) 5" diameter monkey decals
(2) 6"L X 1-1/2"H yellow and red OLD BOY logos
P51GD02 includes:
(1) 6-1/8"L X 2-1/2"H black and white instrument panel
(2) 10"L X 4-1/2"H black and white TJW logos
(2) 2-3/4"L X 1"H white 472 logos (2) white 826 logos
P51GD03 includes: dh
JAL 11/18/97
ir/jl
To make this kit into the P51-B version you would need to order the
following from GREAT PLANES MANUFACTURING at 217-398-8970.
One CANPY097 - canopy
Two P51GBD01 - decal sheet
One P51GBP03 - instrucions for P51GB
One P51GBP04 - Parts List P51GB
One P51GBP01R - plan sheet P51GB
One P51GBF01 - Fuse T-deck formers B8E, B9B, B10B cont.
Parts needed to convert to P-51B cont.
Two P51GW19 - 1/4 x 1/4 x 30" balsa stringers
Two P51GF29 - 1/8 x 3 x 23-7/8" balsa sheet
One P51GBF02 - 5/8 x 3 x 23-7/8" balsa
|
|
|
 |
|
 |
|
|
|
